Sealer'southward Choice® Gold – Rapid Cure is apremiumclass, loftier performance penetrating / impregnating stone, tile & grout sealer. It is a low VOC,h2o-based sealer formulated to provide maximum stain protection, peculiarly in nutrient preparation and serving areas. Ideal for all interior and outside natural stone (including around common salt water swimming pools), tile & grout surfaces. This premium sealer likewise includes born Microban® – Cured Sealant is Mould & Mildew Resistant,and this sealerlasts upwards to xv years.
Cardinal Features:
Maximum stain protection
May be used as a pre-grouting sealer
Allows wet vapour transmission
The NEW Rapid Cure Formula protects in less than 4 hours
Now with built-in Microban® – Cured Sealant is Mould & Mildew Resistant
Safe to utilize, water-based low VOC formula
Does not alter the slip resistance of the sealed surface
Designed to achieve optimal penetration into dense, depression-porosity surfaces
Last up to 15 years
Suitable for apply:
As a natural look sealer for all natural rock surfaces (such as sandstone, slate, quartz, marble, limestone, granite, bluestone / basalt) unglazed tiles, polished & unpolished porcelain tiles, dirt pavers, polished & unpolished concrete, terrazzo, brick, grout, masonry, encaustic tiles, terracotta and grout. Suitable for both interior and exterior use.
Limitations:
Practise non allow sealer to come up in contact with any not-recommended surface.
If the product is allowed to dry out on the surface, a white picture may grade. If this occurs, scrub with Aqua Mix® NanoScrub® and a white nylon pad.
The sealer will not prevent surface wear or etching from acids or caustic chemicals.
Surface Preparation
The surface should exist dry, clean and complimentary of waxes, sealers or finishes. New installations need to be dry 24 hours before application. Protect surrounding surfaces. Examination production in an camouflaged area to ensure desirable results. The Stone, Tile or Grout must be dry prior to applying sealer – the post-obit document explains in particular the definition of the term "dry" every bit it relates to sealer application. READ More
Pre-Grout Sealer / Grout Release:
Porous tile and rock tin can be stained by grout during installation. Sealing the tile before grouting will make grout removal much easier. Apply sealer according to directions afterwards the tile has been bonded for a minimum of 24 hours, or employ to the forepart confront of tile before installation. Expect a minimum of 2 hours earlier grouting.
Procedure
Always test a small area first to ensure satisfactory results.
Apply using a pump sprayer, paint pad applicator, lambswool applicator, sponge or brush.
Allow it to penetrate for upwards to 5 minutes, if the surface is drying within v minutes, apply more sealer to continue surface wet for up to 5 minutes.
Wipe surface completely dry out using clean, dry out cotton wool, paper or microfiber towels after each application. Ensure no sealer is immune to dry out on the surface.
Porous surfaces may require additional applications.
Conduct a test to come across if the surface is completely sealed after 2 hours by applying drops of water on the surface. If it penetrates, an additional awarding is required.
Drying Time
Permit 30 minutes of drying time between applications when weather condition are 20° Celsius and 70% RH.
If temperatures are lower or humidity higher than these times may be longer.
If unsure about the specific job site temperatures and weather condition please contact one of our technical advisors.
Ready for surface traffic in a minimum of ii hours.
Keep dry for a minimum of 12 hours.
Achieves a full cure in a minimum of 24 hours.
Make clean-Up
Make clean tools with mineral spirits afterwards use
Production Data Sheets:
VOC Content:
Maximum VOCs: <70 grams per litre
Available in:
473ml, 946ml, iii.8L, 18.9L
Where to Buy
Production Maintenance:
Routine Cleaning:
Regurlar cleaning should consist of a regular mop or light scrub with a pH neutral detergent, or Aqua Mix Full-bodied Stone & Tile Cleaner at a dilution rate of 1 part product to 80 parts water. Using this product on a regular basis will safely remove soiling and help prevent a stubborn build up without damaging the tile, grout or sealer. This product is a pH Neutral formula and will not impairment any other water-condom surfaces.
Heavy-Duty/Periodic Cleaning (residential):
Pre-moisture the floor with Aqua Mix Stone Deep Clean or Aqua Mix Heavy-Duty Tile & Grout Cleaner at a dilution of 6:1, allow the surface to soak for 3-5 minutes keeping wet.
Then agitate the floor using either an Aqua Mix AquaScrub or rotary floor scrubbing car.
Excerpt liquid off of the floor using either a microfiber mop or a wet vacuum cleaner fitted with a squeegee head.
Rinse thoroughly with clean potable h2o. Mop upwards rinse water off the floor.
Sealer Reapplication: Thoroughly make clean the surface using the periodic cleaning method, then reapply sealer following application instructions as per label. No stripping volition be required for reapplication. Please review specific sealer data sheets for recommended reapplication period.
Aqua Mix Sealers Notes: All spills should be wiped up immediately to reduce the chances of absorption. It is important that no acidic cleaners or products that contain solvents are used on sealed natural stone.
For further data: CLICK Hither
How to Video:
Sealed (left side) Limestone Unsealed (correct side) Water, java, red wine, oil, love apple sauce
Cardinal Features:
Where to Buy 
0 Response to "Aqua Mix 40 Out of 5 Stars 48 Reviews Aqua Mix Sealers Choice Gold"
Post a Comment